FEATURED PRODUCTS
$31,900.00
Omal HBD 1550 Bore Glue and Dowel Machine
Specifications Four working areas Auto selection of the working reference (left, center left, ce...
Specifications Four working areas Auto selection of the working reference (left, center left, center right, right) Center and side reference fences excludable Four double clamps to hold panels either vertically or horizontally for edge or face processing Glue injection system with precision metering of the glue plus checks to make sure glue is shot Standard set up for 8 x 35mm dowel The OMAL “SURE SHOT” revolver system guarantees a dowel is inserted every time! Fiber optic sensor to check if...
$23,950.00
DMC Unisand 2000 53" Orbital Sander
Specifications DMC Unisand 2000 53" Orbital Sander with (2) Pads and (1) Brush Equipped with (2)...
Specifications DMC Unisand 2000 53" Orbital Sander with (2) Pads and (1) Brush Equipped with (2) 10" Wide platens for the elimination of cross-grain scratches; each dual orbital action head equipped with 5.5 HP motor for orbital motion and 1.5 HP motors for side to side movement; each head rotates at 3500 RPM 53" (1350mm) Maximum panel width 2" (52mm) Minimum panel width 16" (400mm) Minimum panel length 6-5/8" (170mm) Maximum panel height 3/16" (4mm) Minimum panel height Abrasive size: 18" x...
$59,000.00
Costa KA CCCT 1350 53" 4-Head Sander
Manufactured in 2004, in very good condition, in a shop with a rigorous PM program 53” wide belt...
Manufactured in 2004, in very good condition, in a shop with a rigorous PM program 53” wide belt 4 head; first head contact drum, 2nd head counter-rotating contact drum, 3rd head contact drum, 4th head, platen, followed by cleaning brush, with constant pass height. In very good condition, in a shop with a rigorous PM program. This was used with a following DMC Unisand 2000 orbital sander, also with constant pass height 480 V, installed power 88 KW Brand Costa Model KA CCCT 1350 Mfg Ye...
$13,500.00
Holz-Her Sprint 1310-6 Edgebander
Specifications Low hours! This machine has fewer than 730 hours of use. Cartridge glue system,...
Specifications Low hours! This machine has fewer than 730 hours of use. Cartridge glue system, with a 3 mm edge thickness capacity, automatic magazine for coil and strips. 3 MM PVC capacity pneumatic guillotine for coil cutoff. Workstations are as follows: Double motor end trim, chamfers 0 - 10 degrees, ((2) 0.22 kW - 9,000 RPM motors), universal top and bottom fine trim for bevels from 0 - 15 degrees, top and bottom profile trimming (1 HP - 22,000 RPM motor each). Top and bottom PVC scrap...
$12,000.00
Holz-Her 1270 Vertical Panel Saw
Specifications Very low hours of use and in very good condition. 75" x 169" Cap., 4 HP motor, 2...
Specifications Very low hours of use and in very good condition. 75" x 169" Cap., 4 HP motor, 2" depth of cut, 220 mm (8-5/8") dia. saw blade at 6,640 RPM. Saw head traverses automatically when rip or crosscutting and returns to starting position; (2) cycle lengths for long or short panels, 36 & 72 FPM saw carriage travel speed, 0.75 HP feed drive; automatically moving back grid w/interlocks. Rip gauge with (3) cam settings, (2) gauging bars throughout frame length with (2) flip stops, ...
